Illig Thermoforming Machines
1. Illig RDM 37/10 (370*250*100mm)
- Form Area 475 x 250 mm
- Film width
495 mm max.
- Max. draw 100 mm.
- Double heating
- Top heater 9.5 kW
- Lower heater 6.9 kW.
-
Lower heater with single heating controller
- Upper heater
with 8x Row control using PD-Temperature controllers and solid state
relays.
- Heaters with pneumatic cylinder retracting mechanism.
- Auto-unwind stand.
- Auto start mechanism.
- Plug assist.
- Air requirement at 6 bar 100 L.
- Dry cycle speed in excess of 35 cycles/ min.
-
Skeletal waste winder.
- Sheet sag control.
-
Machine to be reconditioned and rewired.
2. Illig RDM3715 (370*250*125mm)
- With double heating
- Lower
heater with single heating controller.
- Upper heater
with 8 x Row control using PD-Temperature controllers and solid
state relays.
- Heaters with pneumatic cylinder retracting
mechanism.
- Auto-unwind stand.
- Auto start
mechanism.
- Plug assist.
- Form Area 475 x
250 mm
- Film width 495 mm max.
- Max. draw
150 mm.
- Top heater 9.5 kW
- Lower heater 6.9
kW.
- Air requirement at 6 bar 100 L.
- Cycle
speed in excess of 35 cycles/ min.
- Skeletal waste winder.
- Sheet sag control.
- Machine to be reconditioned
and rewired.
- Motor with brake.
3. Reconditioned
Illig RDM 63/10 (630*250*100mm)
- With auto unwind stand
- Double
heating
- Plug assist
- Skeletal waste material
winder
- Auto-start
- Sheet sag control
- Max. form area 610 x 305 mm max.
- Film width
630 mm
- Max index 320 mm
- Max depth of draw
100 mm
- Max. parent roll dia 1200 mm
- Top
heater 12,2 kW
- Lower heater 10,7 kW
- Heaters
return automatically if machine stops
- Drive motor 3,3
kW
- Air requirement/Cycle at 6 bar 150 L
-
Dry cycle speed in excess of 40 cycles/min.
- The unit
with full Schleicher programmable PLC-Controller and interface Card,
to provide PLC control of all machine functions
i.e. Eliminates the timing cams, also provides
diagnostics
and visual audible warning of
Machine mal-functions.
4. Reconditioned
Illig RDM 63/10 (370*250*100)
-
With auto unwind stand
- Double heating
- Plug
assist
- Skeletal waste material winder
- Auto-start
- Sheet sag control
- Max. form area 610 x 305 mm
max.
- Film width 630 mm
- Max index 320 mm
- Max depth of draw 100 mm
- Max. parent roll dia
1200 mm
- Top heater 12,2 kW
- Lower heater
10,7 kW
- Heaters return automatically if machine stops
- Drive motor 3,3 kW
- Air requirement/Cycle at
6 bar 150 L
- Dry cycle speed in excess of 40 cycles/min.
- The unit with full Schleicher programmable PLC-Controller
and interface Card,
to provide PLC control
of all machine functions
i.e. Eliminates
the timing cams, also provides diagnostics
and
visual audible warning of Machine mal-functions.
5. Illig RDKP54
with DSB65V (Servo Drive)
-
Lentze servo drive sheet Indexing with PLC control for the speed
and the length
- Form Area 500 x 400 mm
- Max.
sheet width 540 mm
- Max. draw +/ - 100 mm
-
Max. index 550 mm
- Top & Bottom heater
-
Top heaters with PID 10 Rows control regular system
-
Form closing force 120 kN
- Inclusive of vacuum pump 70
m
- 25 strokes/ min.
6. Reconditioned Illig RDKP54 with STA95
- Max. Trim Area 650 x 390 mm
-
Max. article height 100 mm
- Trim Force 500 kN.
-
Reconditioned/used Illig RDKP 54 vacuum former with used Trim Press
Illig STA 95
with pneumatic sheet Indexing
- Form Area 500 x 350 mm.
- Max. sheet width 540
mm
- Max. draw +/ - 100 mm
- Max. index 360
mm
- Form closing force 120 kN
- 25 strokes/
min.
- Single top heating. Top Heater with 10 x Row Control
- Sheet Sag control
- Heaters return automatically
in case the sheet sag is too large or if the machine stops.
- Reconditioned Trim Press Illig STA95 with Indexing mechanism.
- Products delivered stacked through the Trim Press Opening.
7. Reconditioned
ILLIG R45 (450*230*80mm)
-
Forming area 450x230mm
- Max. material width 450mm
- Depth of draw, negative 80mm
- Depth of draw positive
80mm
- Max. roll dia. 400mm
- Total power consumption
5 kW
- Max. cycling time depending on material and shape
of forming 20 with trim press.
8. Reconditioned Illig RDM 37/6 (370*250*60mm)
- Auto-unwind stand
- Single heating
- Auto-heater control with Statotherm
Temperature controller
- Heater 7.2 kW
- Heater
profile switchable individually
- Form area 370 x 250
mm
- Plug assist
- Depth of draw 60 mm
-
Auto skeletal waste material winder
- Variable speed-Stroeber
Drive.
- Mechanical speed in excess of 36 cycles/ min.
9. Illig RDKP 54C
- Max. forming area
500x380 mm
- Max. material width 540 mm
- Max.
feed length 400 mm
- Max. depth of draw male/female 120
mm
- Max. table lift 140 mm
- Max. closing force
12000 daN
- Max. no. of cycles of forming tables 35 min
.
|
